XAddHost(3X11) manual page

Name

XAddHost, XAddHosts, XListHosts, XRemoveHost, XRemoveHosts, XSetAccessControl, XEnableAccessControl, XDisableAccessControl, XHostAddress - control host access and host control structure

Syntax

XAddHost(display, host)
Display *display;

XHostAddress *host;

XAddHosts(display, hosts, num_hosts)
Display *display;

XHostAddress *hosts;

int num_hosts;

XHostAddress *XListHosts(display, nhosts_return, state_return)
Display *display;

int *nhosts_return;

Bool *state_return;

XRemoveHost(display, host)
Display *display;

XHostAddress *host;

XRemoveHosts(display, hosts, num_hosts)
Display *display;

XHostAddress *hosts;

int num_hosts;

XSetAccessControl(display, mode)
Display *display;

int mode;

XEnableAccessControl(display)
Display *display;

XDisableAccessControl(display)
Display *display;

Arguments

display: Specifies the connection to the X server.
host: Specifies the host that is to be added or removed.
hosts: Specifies each host that is to be added or removed.
mode: Specifies the mode. You can pass EnableAccess or DisableAccess.
nhosts_return: Returns the number of hosts currently in the access control list.
num_hosts: Specifies the number of hosts.
state_return: Returns the state of the access control.

Description

The XAddHost function adds the specified host to the access control list for that display. The server must be on the same host as the client issuing the command, or a BadAccess error results.

XAddHost can generate BadAccess and BadValue errors.

The XAddHosts function adds each specified host to the access control list for that display. The server must be on the same host as the client issuing the command, or a BadAccess error results.

XAddHosts can generate BadAccess and BadValue errors.

The XListHosts function returns the current access control list as well as whether the use of the list at connection setup was enabled or disabled. XListHosts allows a program to find out what machines can make connections. It also returns a pointer to a list of host structures that were allocated by the function. When no longer needed, this memory should be freed by calling XFree.

The XRemoveHost function removes the specified host from the access control list for that display. The server must be on the same host as the client process, or a BadAccess error results. If you remove your machine from the access list, you can no longer connect to that server, and this operation cannot be reversed unless you reset the server.

XRemoveHost can generate BadAccess and BadValue errors.

The XRemoveHosts function removes each specified host from the access control list for that display. The X server must be on the same host as the client process, or a BadAccess error results. If you remove your machine from the access list, you can no longer connect to that server, and this operation cannot be reversed unless you reset the server.

XRemoveHosts can generate BadAccess and BadValue errors.

The XSetAccessControl function either enables or disables the use of the access control list at each connection setup.

XSetAccessControl can generate BadAccess and BadValue errors.

The XEnableAccessControl function enables the use of the access control list at each connection setup.

XEnableAccessControl can generate a BadAccess error.

The XDisableAccessControl function disables the use of the access control list at each connection setup.

XDisableAccessControl can generate a BadAccess error.

Structures

The XHostAddress structure contains:

0
0>=40 .vs 0u
0<=39 .vs 0p
typedef struct {
    int family;    /* for example FamilyInternet */
    int length;    /* length of address, in bytes */
    char *address;    /* pointer to where to find the address */
} XHostAddress;

The family member specifies which protocol address family to use (for example, TCP/IP or DECnet) and can be FamilyInternet, FamilyDECnet, or FamilyChaos. The length member specifies the length of the address in bytes. The address member specifies a pointer to the address.

Diagnostics