Table of Contents

Name

gluNurbsSurface - define the shape of a NURBS surface

C Specification

void gluNurbsSurface( GLUnurbs* nurb,
    GLint sKnotCount,
    GLfloat* sKnots,
    GLint tKnotCount,
    GLfloat* tKnots,
    GLint sStride,
    GLint tStride,
    GLfloat* control,
    GLint sOrder,
    GLint tOrder,
    GLenum type )

eqn not supported

Parameters

nurb
Specifies the NURBS object (created with gluNewNurbsRenderer).
sKnotCount
Specifies the number of knots in the parametric u direction.
sKnots
Specifies an array of sKnotCount nondecreasing knot values in the parametric u direction.
tKnotCount
Specifies the number of knots in the parametric v direction.
tKnots
Specifies an array of tKnotCount nondecreasing knot values in the parametric v direction.
sStride
Specifies the offset (as a number of single-precision floating point values) between successive control points in the parametric u direction in control.
tStride
Specifies the offset (in single-precision floating-point values) between successive control points in the parametric v direction in control.
control
Specifies an array containing control points for the NURBS surface. The offsets between successive control points in the parametric u and v directions are given by sStride and tStride.
sOrder
Specifies the order of the NURBS surface in the parametric u direction. The order is one more than the degree, hence a surface that is cubic in u has a u order of 4.
tOrder
Specifies the order of the NURBS surface in the parametric v direction. The order is one more than the degree, hence a surface that is cubic in v has a v order of 4.
type
Specifies type of the surface. type can be any of the valid two-dimensional evaluator types (such as GL_MAP2_VERTEX_3 or GL_MAP2_COLOR_4).

Description

Use gluNurbsSurface within a NURBS (Non-Uniform Rational B-Spline) surface definition to describe the shape of a NURBS surface (before any trimming). To mark the beginning of a NURBS surface definition, use the gluBeginSurface command. To mark the end of a NURBS surface definition, use the gluEndSurface command. Call gluNurbsSurface within a NURBS surface definition only.

Positional, texture, and color coordinates are associated with a surface by presenting each as a separate gluNurbsSurface between a gluBeginSurface/gluEndSurface pair. No more than one call to gluNurbsSurface for each of color, position, and texture data can be made within a single gluBeginSurface/gluEndSurface pair. Exactly one call must be made to describe the position of the surface (a type of GL_MAP2_VERTEX_3 or GL_MAP2_VERTEX_4).

A NURBS surface can be trimmed by using the commands gluNurbsCurve and gluPwlCurve between calls to gluBeginTrim and gluEndTrim.

Note that a gluNurbsSurface with sKnotCount knots in the u direction and tKnotCount knots in the v direction with orders sOrder and tOrder must have (sKnotCount - sOrder) $times$ (tKnotCount - tOrder) control points.

Example

The following commands render a textured NURBS surface with normals; the texture coordinates and normals are also NURBS surfaces:

gluBeginSurface(nobj) ; gluNurbsSurface(nobj, ..., GL_MAP2_TEXTURE_COORD_2);
gluNurbsSurface(nobj, ..., GL_MAP2_NORMAL);
gluNurbsSurface(nobj, ..., GL_MAP2_VERTEX_4);
gluEndSurface(nobj) ;

See Also

gluBeginSurface, gluBeginTrim, gluNewNurbsRenderer, gluNurbsCurve, gluPwlCurve


Table of Contents